We use own and third party cookies to improve our services and show content related to your preferences by analyzing your browsing habits.
If you continue using our web, we will consider you accept the use of cookies. You can change the settings or get more information here.

Information

New products

  • Flick Large Case
    Flick Large Case

    Spice up your Flick Large and I2C device with a stylish white and orange...

    22,30 €
  • Flick HAT Case
    Flick HAT Case

    Spice up your Flick HAT and Raspberry Pi with a stylish white and orange...

    15,25 €
  • Flick Zero Case
    Flick Zero Case

    Spice up your Flick Zero and Raspberry Pi Zero with a stylish white and...

    15,25 €

Specials

Components There are 16 products.

per page
Showing 1 - 12 of 16 items
  • 4,00 € In stock

    This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box!

    4,00 €
    In stock
  • 17,95 € In stock

    You could give up OR you could just get our handy PWM and Servo driver shield. It's just like our popular PWM/Servo Breakout but now Arduino-ready and works with any Arduino that uses shields: Uno, Leo, Mega, ADK, its all good.

    17,95 €
    In stock
  • 18,25 € In stock

    Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running.

    18,25 €
    In stock
  • 35,95 € Out of stock

    Bring a little bit of Times Square into your home with this 16 x 32 RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short video clips. We thought they looked really cool so we picked up a few boxes of them from a factory.

    35,95 €
    Add to cart More
    Out of stock
  • 24,95 € In stock

    These LED panels take care of all the work of making a big matrix display. Each panel has six 8x8 red matrix modules, for a 16x24 matrix. The panel has a HT1632C chip on the back with does all the multiplexing work for you and has a 3-pin SPI-like serial interface to talk to it and set LEDs on or off (you cannot set the LED to be individually dimmed, as...

    24,95 €
    In stock
  • 65,00 € In stock

    Bring a little bit of Times Square into your home with this sweet 32 x 32 square RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short video clips. We thought they looked really cool so we picked up a few boxes of them from a factory.

    65,00 €
    In stock
  • 21,25 € Out of stock

    The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors,...

    21,25 €
    Add to cart More
    Out of stock
  • 4,50 € In stock

    We now have a breakout board for a super tiny MEMS microphone. Just like 'classic' electret microphones, MEMS mics can detect sound and convert it to voltage, but they don't need a bias resistor or amplifier, its all in one!

    4,50 €
    In stock
  • 21,65 € In stock

    With the Arduino Robot LCD, you can display text, images, and shapes

    21,65 €
    In stock
  • 8,45 € In stock

    Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task!

    8,45 €
    In stock
  • 15,85 € In stock

    Specifications Antenna type: active (LNA built-in) Supported navigation satellite systems: GPS, GLONASS Dimensions: 45x35x15mm Cable length: 300mm Connector type: MCX Mounting: adhesive

    15,85 €
    In stock
  • 10,95 € In stock

    This pressure sensor from Freescale is a great low-cost sensing solution for precision measurement of barometric pressure and altitude. The MPL3115A2 has a typical 1.5 Pascal resolution, which can resolve altitude at 0.3 meters (compare to the BMP180 which can do 0.17m). It has some upsides compared to the BMP180, such as interrupt outputs for ultra-low...

    10,95 €
    In stock
Showing 1 - 12 of 16 items