We use own and third party cookies to improve our services and show content related to your preferences by analyzing your browsing habits.
If you continue using our web, we will consider you accept the use of cookies. You can change the settings or get more information here.

Assembled Adafruit Feather HUZZAH with ESP8266 WiFi With Headers

ADAF_3046

New product

Feather is the flagship development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

More details

2 Items

In stock

Warning: Last items in stock!

20,45 € tax incl.

Volume discounts

Quantity Discount You Save
5 1% Up to 1,02 €
20 2% Up to 8,18 €
35 3% Up to 21,47 €
50 4% Up to 40,90 €
65 5% Up to 66,46 €
80 6% Up to 98,16 €
100 7% Up to 143,15 €

More info

Description

Feather is the flagship development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

This is the Assembled Adafruit Feather HUZZAH ESP8266 with headers - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB and battery charging and ready to go immediately! Its an  ESP8266 WiFi module with all the extras you need, ready to rock! We have other boards in the Feather family, check'em out here.

At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can program the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. We wired up a USB-Serial chip that an upload code at a blistering 921600 baud for fast development time. It also has auto-reset so no noodling with pins and reset button pressings.

To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available.

Here's some handy specs!

    Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
    Light as a (large?) feather - 9.7 grams
    ESP8266 @ 80MHz with 3.3V logic/power
    4MB of FLASH (32 MBit)
    Built in WiFi 802.11 b/g/n
    3.3V regulator with 500mA peak current output
    CP2104 USB-Serial converter onboard with 921600 max baudrate for uploading
    Auto-reset support for getting into bootload mode before firmware upload
    9 x GPIO pins - can also be used as I2C and SPI
    1 x analog inputs 1.0V max
    Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
    Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
    Power/enable pin
    4 mounting holes
    Reset button

Comes fully assembled and tested, with a USB interface that lets you quickly use it with the Arduino IDE or NodeMCU Lua (it comes preprogrammed with the Lua interpreter). This version of the board has also been pre-soldered, so you can plug it right into a solderless breadboard. Click here for the un-soldered version. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)


Technical Details

    23mm x 51mm x 18mm / 0.9" x 2" x 0.71"
    Weight: 8g